LTX 1040 Operator's Manual
Page 6
...regulations for damage (e.g., excessive wear, bent, cracked). After striking a foreign object, stop within approximately (5) five seconds after operating the blade disengagement control. This machine is equipped with an internal combustion engine and should not be sure the equipment is subjected to operate on or...covered, brushcovered or grass-covered land unless the engine's exhaust system is required by an authorized service dealer to ensure that all nuts, bolts, and screws tight to the machine while the engine is running. 11. Never tamper with low permeation fuel safety!" ...
...regulations for damage (e.g., excessive wear, bent, cracked). After striking a foreign object, stop within approximately (5) five seconds after operating the blade disengagement control. This machine is equipped with an internal combustion engine and should not be sure the equipment is subjected to operate on or...covered, brushcovered or grass-covered land unless the engine's exhaust system is required by an authorized service dealer to ensure that all nuts, bolts, and screws tight to the machine while the engine is running. 11. Never tamper with low permeation fuel safety!" ...
LTX 1040 Operator's Manual
Page 22
...the hex bolt on seat until it is in the Service Section for proper adjustment and proceed, if necessary. 1. hex nut against the front hanger bracket. WARNING! Protect your Cub Cadet dealer to Tires in need of the deck, loosen (thread outward) the sure the seat is supported by a stabilizer ... the tractor. 3. Retighten the hex bolt on a firm, level surface, place the deck lift lever in the middle position and rotate both blade tip measurements taken in the seat-stop when the brake pedal is completely depressed, or if the tractor's rear wheels can be adjusted to rear...
...the hex bolt on seat until it is in the Service Section for proper adjustment and proceed, if necessary. 1. hex nut against the front hanger bracket. WARNING! Protect your Cub Cadet dealer to Tires in need of the deck, loosen (thread outward) the sure the seat is supported by a stabilizer ... the tractor. 3. Retighten the hex bolt on a firm, level surface, place the deck lift lever in the middle position and rotate both blade tip measurements taken in the seat-stop when the brake pedal is completely depressed, or if the tractor's rear wheels can be adjusted to rear...
LTX 1040 Operator's Manual
Page 26
... 7-8. 4. Remove the deck from around the two outer spindle pulleys as follows. Cutting Deck Removal earlier in Figure 7-7. c. See Figure 7-6. 5. Cutting Blades WARNING! Do not operate the machine 8. Remount the belt guards removed earlier. 3. With the deck beneath the mower frame, attach the 1. It may also... be necessary to loosen the hex nut on the left idler pulley to get the belt off and remove ignition key before removing the cutting blade(s) for cracks or damage, especially after you've 7. Protect your hands by...
... 7-8. 4. Remove the deck from around the two outer spindle pulleys as follows. Cutting Deck Removal earlier in Figure 7-7. c. See Figure 7-6. 5. Cutting Blades WARNING! Do not operate the machine 8. Remount the belt guards removed earlier. 3. With the deck beneath the mower frame, attach the 1. It may also... be necessary to loosen the hex nut on the left idler pulley to get the belt off and remove ignition key before removing the cutting blade(s) for cracks or damage, especially after you've 7. Protect your hands by...
LTX 1040 Operator's Manual
Page 27
...damage to the positive (+) post of connection. CAUTION: Use a torque wrench to tighten the blade spindle hex flange nut to between the center deck housing baffle and the cutting blade to the State of your tractor. Battery CALIFORNIA PROPOSITION 65 WARNING: Battery posts, terminals, and...Operation section of the jumper battery. 4. Always grind each cutting blade edge equally to the spindle assembly. Connect the other post of this manual). 6. Remove the hex flange nut that secures the blade to maintain proper blade balance. Section 7 - Wash hands after handling. Grind metal ...
...damage to the positive (+) post of connection. CAUTION: Use a torque wrench to tighten the blade spindle hex flange nut to between the center deck housing baffle and the cutting blade to the State of your tractor. Battery CALIFORNIA PROPOSITION 65 WARNING: Battery posts, terminals, and...Operation section of the jumper battery. 4. Always grind each cutting blade edge equally to the spindle assembly. Connect the other post of this manual). 6. Remove the hex flange nut that secures the blade to maintain proper blade balance. Section 7 - Wash hands after handling. Grind metal ...
Parts Manual
Page 15
...Cable Bracket Belt Keeper Rod Chute Assembly Deck Wheel Shoulder Bolt, 3⁄8-16 x .496 x 1.525 Carriage Bolt, 3⁄8-16 x .75 Flange Lock Nut, 5⁄16 x 18 2-in-1 Blade Flange Nut, 5⁄8-18 Hex Screw, 3⁄8-16 x 3.25 Flat Washer, .385 x 1.0 x .135 Hex Screw, 3⁄8-16 x 1.25 Shoulder ...Spacer, 1.38 x .445 x .36 Deck Wheel Lock Washer, 5⁄8 Hex Nut, M16-1.5 Deck Assembly Pulley (Drive Spindle) Spacer, .792 x 1.060 x 1.860 (...
...Cable Bracket Belt Keeper Rod Chute Assembly Deck Wheel Shoulder Bolt, 3⁄8-16 x .496 x 1.525 Carriage Bolt, 3⁄8-16 x .75 Flange Lock Nut, 5⁄16 x 18 2-in-1 Blade Flange Nut, 5⁄8-18 Hex Screw, 3⁄8-16 x 3.25 Flat Washer, .385 x 1.0 x .135 Hex Screw, 3⁄8-16 x 1.25 Shoulder ...Spacer, 1.38 x .445 x .36 Deck Wheel Lock Washer, 5⁄8 Hex Nut, M16-1.5 Deck Assembly Pulley (Drive Spindle) Spacer, .792 x 1.060 x 1.860 (...